home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
EnigmA Amiga Run 1996 June
/
EnigmA AMIGA RUN 08 (1996)(G.R. Edizioni)(IT)[!][issue 1996-06][EARSAN CD VII].iso
/
earcd
/
comm3
/
jans110l.lha
/
janos
/
nl0jor
/
help
/
tcp
< prev
next >
Wrap
Text File
|
1995-12-30
|
4KB
|
116 lines
tcp <subcommand>
These commands are used for the Transmission Control Protocol
service.
Notes:
Attempting outgoing connections to addresses without an
existing route result in Error number 19.
tcp irtt [<milliseconds>]
(B) Display or set the initial round trip time estimate, in
milliseconds, to be used for new TCP connections until they can
measure and adapt to the actual value. The default is 5000
milliseconds (5 seconds). Increasing irtt when operating over
slow channels will avoid the flurry of re-transmissions that
would otherwise occur as the smoothed estimate settles down at
the correct value. Note that this command should be given before
servers are started in order for it to have effect on incoming
connections.
TCP also keeps a cache of measured round trip times and mean
deviations (MDEV) for current and recent destinations. Whenever
a new TCP connection is opened, the system first looks in this
cache. If the destination is found, the cached IRTT and MDEV
values are used. If not, the default IRTT value mentioned above
is used, along with a MDEV of 0. This feature is fully
automatic, and it can improve performance greatly when a series
of connections are opened and closed to a given destination (e.g.
a series of FTP file transfers or directory listings).
tcp kick <tcb_addr>
If there is unacknowledged data on the send queue of the
specified TCB, this command forces an immediate retransmission.
<tcb addr> can be found with the 'tcp status' command.
tcp maxwait [<msec>]
Set or show the maximum time for retry timeout in milliseconds.
Default = 0, no maximum.
tcp mss [<size>]
(B) Display or set the TCP Maximum Segment Size in bytes that
will be sent on all outgoing TCP connect request (SYN segments).
This tells the remote end the size of the largest segment
(packet) it may send. Changing MSS affects only future
connections; existing connections are unaffected. See also the
section ON MTU, etc.
tcp reset <tcb_addr>
Deletes the TCP control block at the specified address.
tcp retries [<num>]
(B) Display or set the number of retries before a tcp connection
will be reset. Default is 16. This is useful to eliminate idle
connections that have not been properly shut down. Default = 0,
there is no maximum, i.e. a connection will never retry out.
tcp rtt <tcb_addr> <milliseconds>
Replaces the automatically computed round trip time in the
specified TCB with the rtt in milliseconds. This command is
useful to speed up recovery from a series of lost packets since
it provides a manual bypass around the normal backoff
retransmission timing mechanisms.
tcp status [<tcb_addr>]
Without arguments, displays several TCP-level statistics, plus a
summary of all existing TCP connections, including TCB
address, send and receive queue sizes, local and remote sockets,
and connection state. If <tcb addr> is specified, a more
detailed dump of the specified TCB is generated, including send
and receive sequence numbers and timer information.
tcp syndata [yes | no]
(B) Display or set the tcp syn + data piggybacking flag. Some
tcp systems cannot handle syn + data together.
tcp timertype [linear | exponential]
(B) Display the current setting or set the timer type backoff
algorithm. Default is linear.
tcp trace [yes | no]
(B) Display or set the tcp trace flag on or off.
tcp window [<size>]
(B) Displays or sets the default receive window size in bytes to
be used by TCP when creating new connections. Existing
connections are unaffected.